Nipro SURDIAL Скачать руководство пользователя страница 293 | Manualshive

Страница: 293 / 334

Nipro SURDIAL Скачать руководство пользователя страница 293

10.19-1

10.19. Adjustment of flushing volume in concentrate line

ܭ

CAUTION

z

The flushing volume between V17 line for acid rinse (optional unit) and V12 line is same.

The length of each line must be same.

z

Adjust flushing volume when the length of concentrate line is changed.

z

Initialized value of flushing volume is different between after ROM ver.3.84 and ver.3.70.

Adjust flushing volume when ROM version upgrade.

NOTE

z

Enabled adjustment of flushing volume after ROM version 3.84.

z

Flushing means that water is flowed in concentrate line after chemical or acid rinse.

Flushing is performed when machine aspirates concentrate during chemical or acid rinse.

10.19.1.Confirmation of flushing volume

Confirm flushing volume after air is filled in concentrate line.

(1) Remove right cover from upper part of machine and right cover from lower part of it to expose

dipswitch on the main PCB.

(2) Turn on DIPSW1.
(3) Remove concentrate line from V12 and then remove fluid inside silicone tube under

connecting concentrate connector for disinfectant. Return concentrate line to V12 after
removal of fluid.

(4)  Turn on [DIALYSIS] SW to shift to dialysis wait process.
(5)  Select “RINSE2:CHEMICAL” in rinse menu.
(6)  Turn on [RINSE] SW to shift to chemical rinse process.

Confirm opening of V12 and then machine shift to aspirate concentrate under maintenance
mode 4.

ACID

DISINFECTANT

IN

OUT

IN

OUT

<V17>

V12

Concentrate line

«
...
291
292
293
294
295
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов