Nipro SURDIAL Скачать руководство пользователя страница 296

Страница: 296 / 334

10.20-2

(6) Turn on [RINSE] SW to shift to chemical rinse process.
(7) Concentrate is aspirated after chemical rinse is started.

First aspiration of concentrate is priming. Confirm concentrate is flowed over V12.

Adjustment range

Priming volume

From concentrate tank to after V12

(8) Turn off DIPSW1and then return the removed covers to the original position.

10.20.2. Adjustment of priming volume

Adjust priming volume by inputting offset value in maintenance mode 6.

(1) Release setting protection by selecting ON of “25.MAITENANCE MODE FREE”in

maintenance mode 7 screen.

(2) Input “21. CHM PRIM VOL.OFFSET” in maintenance mode 6.

Adjustment screen

Priming volume

Maintenance mode 6
21.CHM PRIM VOL.OFFSET

Input +1

Shift concentrate to machine side

Input –1

Shift concentrate to concentrate tank side

(3) Protect setting by selecting OFF of “25.MAINTENANCE MODE FREE”in maintenance mode 7

screen.

(4) Turn off power SW of machine.

The range of priming

Содержание SURDIAL















































































































































































































































































































































Результаты поиска

Содержание SURDIAL

Отзывы:

Nipro SURDIAL, Руководство по обслуживанию, Страница: 296 / 334

Результаты поиска

Содержание SURDIAL

Отзывы: