Nipro SURDIAL Скачать руководство пользователя страница 274 | Manualshive

Страница: 274 / 334

Nipro SURDIAL Скачать руководство пользователя страница 274

10.13-2

(10)  Set blood pump flow rate to 400mL/min and operate the pump.
(11)  Measure actually discharged water weight or volume/minute (mL/min).
(12)  Input “17.BPF(GAIN)” value of blood pump flow rate in maintenance mode 6 screen value to

try to adjust the actual flow rate to about 400mL/min. Decrease (increase) the value if the
actual flow rate is higher (lower) than the set flow rate.

(13) Repeat the above procedures (7) to (12) until each of the actual flow rates of 50 and

400mL/min is obtained.

Blood pump flow rate

Adjusting value

50mL/min

Maintenance mode 6 screen 18.BPF(OFFSET)

400mL/min

Maintenance mode 6 screen 17.BPF(GAIN)

(14) Protect setting by selecting ON of “20.MAINTENANCE MODE FREE” in maintenance mode 7

screen.

10.13.2 In case of you use Small Rolling Tube( 6.35× 9.75mm)

(1) See chapter 10.12 and adjust gaps between housing and rotor rollers by using Small Rolling

Tube.

(2)  Change “NORMAL” to “SMALL” at [19.ROLLING TUBE TYPE] in Maintenance mode 6.
(3)          (Max blood flow is 350mL/min)
(4)  Set 2 pies of Tube holder(See Chapter 6.2 of Operation Manual) at inlet and outlet of Blood

pump unit.

(5) See chapter 10.13.1 and adjust blood pump flow as same method. But adjust 50mL/min to

OFFSET and adjust 250mL/min to GAIN.

Blood pump flow rate

Adjusting value

50mL/min

Maintenance mode 6 screen 18.BPF(OFFSET)

250mL/min

Maintenance mode 6 screen 17.BPF(GAIN)

«
...
272
273
274
275
276
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов