Nipro SURDIAL Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 334

Nipro SURDIAL Скачать руководство пользователя страница 291

10.18-1

10.18. Adjustment of gas purge pressure

Adjust pressure during gas purge. Adjust pressure by turning adjusting screw of pinch cock 2 (PC2)
under monitoring dialysate pressure in dialysis screen based on the following procedures.

(1)  Remove left cover from under part of machine to expose PC2.
(2)  Turn on power SW of machine.
(3)  Release  setting  protection  by  selecting  ON  of  “20.MAINTENANCE  MODE  FREE”  in

maintenance mode 7.

(4)  Set “8.MODE” to W in maintenance mode 5.
(5)  Turn on [DIALYSIS]SW to shift to dialysis wait process.
(6)  Press [PREP.]SW to shift preparation process.
(7)  Check stabilization of dialysate temperature.
(8)  Work gas purge by shorting connector of FSW in AS2 using conducted material.
(9)  Adjust gas purge pressure 0-100 mmHg during priming by turning adjusting screw of PC2

under monitoring dialysate pressure in dialysis screen.

Turning adjusting screw counterclockwise

Reduce gas purge pressure

Turning adjusting screw clockwise

Increase gas purge pressure

Tube should be centered at PC2 and plates of PC2 should be aligned correctly.

Fig.10.18-1 Adjustment of pinch cock

(10)  Apply adhesive or the like to adjusting screw of PC2 for fixing.
(11)  Turn off [DIALYSIS]SW to shift to dialysis wait process.
(12)  Return to setting “8.MODE” in maintenance mode 5.
(13)  Protect setting by selecting OFF of “20.MAINTENANCE MODE FREE” in maintenance mode

7 screen.

(14) Turn off power SW of machine.
(15) Return the removed covers to the original positions.

NOTE

z

Confirm to regular value in “8.D.PRESS OFFSET” in maintenance mode 6 before adjustment of

gas purge pressure.

z

Adjust gas purge pressure within 50±20 mmHg.

«
...
289
290
291
292
293
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов