Nipro SURDIAL Скачать руководство пользователя страница 294

Страница: 294 / 334

10.19-2

(7) Skip chemical rinse process by pressing [RINSE] SW after confirmation of opening V12.
(8) Perform flushing after skipping chemical rinse process.

Confirm concentrate is flowed to the middle of FEP tube.

Adjustment range

Flushing volume

The middle of FEP tube

(9) Turn off DIPSW1and then return the removed covers to the original position.

10.19.2 Adjustment of flushing volume

Adjust flushing volume by inputting offset value in maintenance mode 6.

(1) Release setting protection by selecting ON of “25.MAITENANCE MODE FREE”

in maintenance mode 7 screen.

(2) Input “20. FLUSHBACK VOLUME OFFSET” in maintenance mode 6.

Adjustment screen

Flushing volume

Maintenance mode 6
20.FLUSHBACK VOLUME OFFSET

Input +

Shift concentrate to concentrate tank side.

Input –1

Shift concentrate to machine side

(3) Protect setting by selecting OFF of “25.MAINTENANCE MODE FREE”in maintenance mode 7

screen.

(4) Turn off power SW of machine.

The range of flushing

Содержание SURDIAL















































































































































































































































































































































Результаты поиска

Содержание SURDIAL

Отзывы:

Nipro SURDIAL, Руководство по обслуживанию, Страница: 294 / 334

Результаты поиска

Содержание SURDIAL

Отзывы: