Nipro SURDIAL Скачать руководство пользователя страница 265 | Manualshive

Страница: 265 / 334

Nipro SURDIAL Скачать руководство пользователя страница 265

10.10-1

10.10. Adjustment of priming flow rate

10.10.1. Adjustment by Flow meter

Adjust priming flow rate of water by turning control valve NV1 by measuring discharge flow rate
which is substantially same as priming flow rate. Follow the below procedures.

(1) Required device

Flow meter

(2)  Remove right cover from lower part of machine to expose NV1.
(3)  Connect flow meter to discharge port to measure discharge flow rate.
(4)  Turn on power SW of machine.
(5)  Turn on [DIALYSIS] SW to shift to dialysis wait process.
(6)  Release  setting  protection  by  selecting  ON  of  “20.MAINTENANCE  MODE  FREE”  in

maintenance mode 7 screen.

(7) Set machine operation to console mode by selecting ON of “19.CONSOLE MODE” in

maintenance mode 7 screen.

(8)    By pressing [PRIP.] SW to shift to preparation process, machine is started from console mode.
(9)    Check dialysate temperature stabilization.
(10)  During V2 is ON, adjust discharge flow rate from 700 to 750ml/min by turning adjusting screw

of NV1 by referring to data in maintenance mode 4 screen. V2 should not be OFF.

Adjusting value

Priming flow rate

700 750mL/min

(11) Turn on [DIALYSIS] SW to shift to dialysis wait process.
(12) Release console mode by selecting OFF of “19.CONSOLE MODE” in maintenance mode 7

screen.

(13) Protect setting by selecting OFF of “20.MAINTENANCE MODE FREE” in maintenance mode 7

screen.

(14) Remove the flow mater to return to the original condition.
(15) Return the removed cover to the original position.

«
...
263
264
265
266
267
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов