Nipro SURDIAL Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 334

Nipro SURDIAL Скачать руководство пользователя страница 152

8.5-2

Replacement

ܭ

CAUTION

z

Replace dialysate pressure sensor board after turning off power SW of machine under care not

to be charged with static electricity.

(1)  Turn off power SW of machine.
(2)  Remove left cover from upper part of machine and left cover from lower part of it.
(3)  Remove  dialysate  pressure  sensor  ASSY  as  per  the  procedure  specified  in  “6.1.2  Dialysate

pressure sensor ASSY-TYPE I”.

(4)  Disconnect all connectors.
(5)  Loosen screws used to fix dialysate pressure sensor board to remove it.
(6)  Prepare new dialysate pressure sensor board.
(7)  Attach the new board.
(8)  Connect all the disconnected connectors.
(9)  Attach dialysate pressure sensor ASSY.
(10)  Turn on power SW of machine.
(11)  Adjust  dialysate  pressure  sensor  as  per  the  procedure  specified  in  “10.3.1.  Adjustment  of

dialysate pressure sensor”.

(12) Check correct function of dialysate pressure sensor.
(13) Return the removed covers to the original positions.

«
...
150
151
152
153
154
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов