Nipro SURDIAL Скачать руководство пользователя страница 153

Страница: 153 / 334

8.5-3

8.5.2. TYPE II: A Type

Fig. 8.5-2 Dialysate pressure sensor board (TYPE II: A Type)

General description and function

Dialysate pressure sensor board is placed at top of lower part of machine.

The board is used to measure pressure in dialysate line in cooperation with dialysate pressure

sensor.

Connection

CN1 Connect to CN14 of [main board ] through harness.

CN2 Connect of connector of [dialysate pressure sensor].

Adjustment

See “10.3.2. Adjustment of dialysate pressure sensor TYPE II”.

Replacement

Do not replace only dialysate pressure sensor board.
Replace all Assy when replace dialysate pressure sensor board.

Содержание SURDIAL















































































































































































































































































































































Результаты поиска

Содержание SURDIAL

Отзывы:

Nipro SURDIAL, Руководство по обслуживанию, Страница: 153 / 334

Результаты поиска

Содержание SURDIAL

Отзывы: