Nic MA-3 Solo Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 152

Nic MA-3 Solo Скачать руководство пользователя страница 19

Instruction Manual: Thermal Vaporization Mercury Analyzer MA-3

Solo

NIC-TD-0000090-15

12

Nippon Instruments Corporation

3.

Installation and Connection

3.1.

Installation of Instrument

Danger

Do not put any inflammable or combustible around the instrument.
Otherwise, a fire may result.

Warning

If there is any risk of generation of any harmful gasses such as
halogen, sulfur and selenium during decomposition by heating, please
be sure to vent the exhaust gas.

Caution



Be sure to use the supplied power cable.
If another cable is used, it may cause a failure.



Observe installation requirements and power specifications.
Otherwise, a failure may result.



Install the instrument on a horizontal working table with sufficient
strength.
Otherwise, a failure or a minor injury caused by an overturn or a
fall may result.



Secure space of 150 mm or more in the rear for hot exhaust
(general exhaust) from the rear upper part of the instrument and
work space to turn on or off the instrument.



Be sure to avoid a room for using an organic chlorine solvent or a
halogen reagent such as potassium iodide.
Also avoid a room into which the gas of the above-mentioned
reagent may flow.
Such substances become the cause of trouble such as the
sensitivity fall of the instrument.

(1)

Put the MA-3

Solo

and PC in the installation position.

For installation requirements and an installation layout, refer to “8. Installation

Requirements”.

(2)

Install necessary software according to “3.2 Installation and uninstallation of PC

*

Be sure to carry out Step (2) before Step (5).

Otherwise, the installation of software and control will be impossible.

(3)

Connect the power cable to the AC inlet in the rear of the MA-3

Solo

.

(4)

Connect the power cable to an outlet with the ground.

(5)

Connect the MA-3

Solo

and the PC using a USB cable.

(6)

Connect the exhaust port in the rear of the instrument to a draft or the like.

(7)

To automatically measure the sample weight by using the balance, connect the

cable between the balance and PC.

* Please refer to the instruction manual of the balance for the detail of connection.

* The cable is not included. Please prepare separately.

«
...
17
18
19
20
21
...
»

Содержание MA-3 Solo

























































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды