Nic MA-3 Solo Скачать руководство пользователя страница 13

Страница: 13 / 152

Instruction Manual: Thermal Vaporization Mercury Analyzer MA-3

Solo

NIC-TD-0000090-15

Nippon Instruments Corporation

2.2.

Principle of Measurement

A sample is heated in the H1 (sample heater), and the mercury compound in the

sample is made to evaporate. Then, the catalyst furnace (H2) decomposes a mercury

compound in gas, removes interfering components and atomizes mercury.

The interfering components are removed by managing the mercury collector tube to an

appropriate temperature using the H3, and the collection concentration is carried out

selectively for the mercury gas as gold amalgam.

After the completion of the sample heating decomposition sequence, the mercury

collector tube is heated, mercury is separated again as metal mercury gas and is led to

the detection unit (absorption cell), and the absorbance at 253.7 nm, which is the first

absorption wavelength band of mercury, is measured.

Heater H3

(Mercury Collector Tube

Heating Furnace)

Mercury

Collector Tube

Heater H2

(Catalyst Furnace)

Heater H1

(Sample Heating Furnace)

Heater H4

Detector

Absorption

Cell

Lamp

Detector

Drain Bottle

Humidifica-

tion Bottle

Needle Valve

Air Pump Flow Sensor

Activated

Carbon Filter

Activated Carbon Filter

Nafion Tube

Exhaust

Air

Filter Unit

Содержание MA-3 Solo

























































































































































Результаты поиска

Содержание MA-3 Solo

Отзывы:

Бренды по названию

Популярные бренды

Nic MA-3 Solo, Инструкция по эксплуатации

Результаты поиска

Содержание MA-3 Solo

Отзывы:

Бренды по названию

Популярные бренды