Nic MA-3 Solo Скачать руководство пользователя страница 130

Страница: 130 / 152

Instruction Manual: Thermal Vaporization Mercury Analyzer MA-3

Solo

NIC-TD-0000090-15

Nippon Instruments Corporation

123

Warning

Before using a reagent, procure and administer the safety data sheet
(SDS).

Please use the following grease for the inlet.

We cannot guarantee the instrument performance if the following grease is not used.

[SUMICO LUBRICANT CO., LTD. Sumitec 103]

[SUMICO LUBRICANT CO., LTD. Sumiplex MP No.2]

(1)

According to steps (1) to (2) in “6.6.5 Replacement and Cleaning of Boat In/Out Rod”

described above, remove the boat in/out rod.

(2)

Remove grease from the following two thread parts (yellow parts).

* If the type of grease is changed, make sure to wipe off the old grease.

Mixing different types of grease can interfere the performance.

(3)

Apply grease to the thread part of the boat in/out side (yellow part) above.

Use a toothpick or the like and take care not to apply grease to any other place.

(4)

According to steps (7) and (8) in “6.6.5 Replacement and Cleaning of Boat In/Out

Rod” described above, attach the boat in/out rod as before.

the boat in/out side

the inlet side

Содержание MA-3 Solo

























































































































































Результаты поиска

Содержание MA-3 Solo

Отзывы:

Бренды по названию

Популярные бренды

Nic MA-3 Solo, Инструкция по эксплуатации

Результаты поиска

Содержание MA-3 Solo

Отзывы:

Бренды по названию

Популярные бренды