NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 280 / 406

background image

9-6 Upgrading Your Server

DEVICE INSTALLATION OR REMOVAL PROCEDURE

Install or remove a component from the server in the following procedure.

Hard Disk Drive

The server has six device bay slots to install hard disk drives with the SCA2 interface (Ultra 320
SCSI) in the disk bay of the front of the server.

IMPORTANT:

Do not use any hard disk drives that are not authorized by NEC.
Installing a third-party hard disk drive may cause a failure of the
server as well as the hard disk drive. Purchase hard disk drives of
the following models:
<SCSI>
– N8150-163F (73.2 GB, 10,000 rpm, Ultra 320)
– N8150-171F (146 GB, 10,000 rpm, Ultra 320)
– N8150-192 (300 GB, 10,000 rpm, Ultra 320)
– N8150-165F (36.3 GB, 15,000 rpm, Ultra 320)
– N8150-172F (73.2 GB, 15,000 rpm, Ultra 320)
– N8150-193 (146 GB, 15,000 rpm, Ultra 320)
<SAS: when N8154-10 SAS back panel is installed>
– N8150-199 (36.3 GB, 15,000 rpm, SAS)
– N8150-200 (73.2 GB, 15,000 rpm, SAS)
– N8150-201 (146 GB, 15,000 rpm, SAS)

To make array configuration, specify RAID0, RAID1, or RAID5 as
the RAID level.

Up to six hard disk drives can be installed in standard mode. If
using the flex bay, you can install up to seven hard disk drives.

«
...
278
279
280
281
282
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Бренд: Panasonic Страницы: 28

MCX-2000 - MusicCAST Digital Audio Server

Бренд: Yamaha Страницы: 25

Portbase PB-3010

Бренд: SystemBase Страницы: 45

eServer BladeCenter HS40 Type 8839

Бренд: IBM Страницы: 120

Бренд: Olive Страницы: 44

Бренд: MISUMI Страницы: 18

4-Port USB 2.0 Device Server over IP...

Бренд: Quatech Страницы: 2

Бренд: Belkin Страницы: 2

Бренд: Excito Страницы: 3

Бренд: Planet Страницы: 95

Бренд: Corvus systems Страницы: 108

SuperWorkstation 5049A-TR

Бренд: Supermicro Страницы: 189

SuperStorageServer SSG-6119P-ACR12N4L

Бренд: Supermicro Страницы: 211

Бренд: LG-Ericsson Страницы: 54

Com Port Redirector

Бренд: Lantronix Страницы: 31

Бренд: ICPDAS Страницы: 30

Бренд: 3onedata Страницы: 3

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды