NEC Express5800/120Rh-2 Скачать руководство пользователя

Страница: 29 / 406

Notes on Using Your Server 1-13

TRANSFER TO THIRD PARTY

The following must be observed when you transfer (or sell) the server or software provided with the
server to a third party:

Server Hardware

Make sure to provide this User's Guide along with the server to a third party.

Provided Software

To transfer or sell any software application that comes with the server to a third party, the following
requirements must be satisfied:

All provided software applications must be transferred and no backup copies must be
retained.

Transfer requirements listed in "Software License Agreement" that comes with each
software application must be satisfied.

Software applications that are not approved for transfer must be uninstalled before
transferring the server.

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды