NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 257 / 406

background image

Troubleshooting 8-21

Problems with NEC EXPRESSBUILDER

When the server is not booted from the NEC EXPRESSBUILDER CD-ROM, check the following:

T

Did you set the NEC EXPRESSBUILDER during POST and restart the server?

→

If you do not set the NEC EXPRESSBUILDER during POST and restart the
server, an error message will appear or the OS will boot.

T

Is BIOS configuration correct?

→

The boot device order may be specified with the BIOS SETUP utility of the server.
Use the BIOS SETUP utility to change the boot device order to boot the system
from the CD-ROM drive first.

<Menu to check: [Boot]>

T

Is an error message appeared?

→

When an error occurs while the NEC EXPRESSBUILDER is in progress, the
following message appears. After this message appears, check the error and take
the appropriate corrective action according to the message listed in the table
below.

Message

Cause and Remedy

This machine is not supported.

This NEC EXPRESSBUILDER version is not
designed for this server. Execute the NEC
EXPRESSBUILDER on the compliant server.

NvRAM access error

An access to the nonvolatile memory
(NvRAM) is not acceptable.

Hard disk access error

The hard disk drive is not connected or it is
failed.
Check whether the hard disk drive is correctly
connected.

The system-specific information
does not exist on the baseboard.
Please restore the backup data
or write the data by using
[System Information
Management] of the Off-line
Maintenance Utility.
Only the authorized personnel
are allowed to do this operation.

The system-specific information can't be
acquired in the mother board exchange and
so on.

«
...
255
256
257
258
259
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Бренд: Lanner Страницы: 43

ioLogik W5300 Series

Бренд: Moxa Technologies Страницы: 177

ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER

Бренд: Novell Страницы: 390

DocuColor 45087638

Бренд: Xerox Страницы: 28

DiskStation Series

Бренд: Synology Страницы: 6

Бренд: Advantech Страницы: 43

Бренд: TYAN Страницы: 81

Бренд: Atop Страницы: 2

Бренд: Epson Страницы: 28

EpsonNet 802.11b

Бренд: Epson Страницы: 30

Stylus C80WN - Ink Jet Printer

Бренд: Epson Страницы: 1

Бренд: Epson Страницы: 258

Бренд: Epson Страницы: 280

Eternus DX80 S2

Бренд: Fujitsu Страницы: 186

Бренд: Fujitsu Страницы: 242

ConnectPort LTS 16

Бренд: Digi Страницы: 169

6180DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Z Microsystems Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды