NEC Express5800/120Rh-2 Скачать руководство пользователя

Страница: 89 / 406

Setting Up Your Server 3-15

Hold the handle and pull out the server from the rack slowly and carefully.

The server clicks to be latched.

Pull out the server from the rack with the right and left release lever pressed to release the
latch.

IMPORTANT:

Pull out the server slowly holding the bottom of the server by at
least two persons.

Do not apply any load on the server pulled out from the rack.
Doing so may cause personal injury if the server drops.

To remove some mechanical parts of the rack, see the installation procedure.

Release lever

Captive thumb screws

Handles

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды