NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 255 / 406

background image

Troubleshooting 8-19

Problems with Windows Server 2003 and Windows 2000

Cannot install the operating system correctly.

T

Did you confirm the notes on installing the operating system?

→

See Chapter 6.

During Windows 2000 installation, the following warning is registered in the System Log of the
Event Viewer:

Error detected on the device \Device\CdRom0
during the paging operation.

→

There is no problem on this issue.

Fail to start the OS:

T

Is a floppy disk in the floppy disk drive?

→

Take out the floppy disk and restart the server.

T

Is the NEC EXPRESSBUILDER CD-ROM in the CD-ROM drive?

→

Take out the NEC EXPRESSBUILDER CD-ROM and restart the server.

T

Is the OS broken?

→

Use recovery process to recover the system. (See "Recovery for Windows 2000
System" in this Chapter.)

The event log after every logon to Windows 2000 includes the following error log:

Description (D)
The CPUs in this multiprocessor system are not all the same revision level.
To use all processors the operating system restricts itself to the features of
the least capable processor in the system. Should problems occur with
this system, contact the CPU manufacture to see if this mix of processors
is supported.

T

Has the CPU been expanded?

→

If the different revision (stepping) of the processor is installed in the
multiprocessor system, Windows logs the above information every startup. If
this message is logged, it is no problem for operation.

The OS presents unstable operation:

T

Did you update the system?

→

Installing a network drive after installation of the OS may cause unstable
operation. Use the NEC EXPRESSBUILDER CD-ROM to update the system.
(See Chapter 6.)

«
...
253
254
255
256
257
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Бренд: IBM Страницы: 88

Бренд: Xerox Страницы: 12

Бренд: NAIM Страницы: 16

Бренд: Qlogic Страницы: 20

Бренд: Vicon Страницы: 2

Бренд: US Robotics Страницы: 156

Бренд: Hawking Страницы: 40

Бренд: RackSolutions Страницы: 8

SUPERSERVER 5017C-MF

Бренд: Supero Страницы: 96

8668 - Eserver xSeries 232

Бренд: IBM Страницы: 182

Бренд: Atop Страницы: 2

PRIMERGY TX2540 M1

Бренд: Fujitsu Страницы: 92

PRIMERGY TX200 S5

Бренд: Fujitsu Страницы: 114

PRIMERGY TX300 S5

Бренд: Fujitsu Страницы: 142

PRIMERGY TX200 S6

Бренд: Fujitsu Страницы: 126

Server PRIMERGY TX1330 M1

Бренд: Fujitsu Страницы: 336

PRIMERGY TX300 S6

Бренд: Fujitsu Страницы: 122

Бренд: Fujitsu Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды