NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 46 / 406

background image

2-14 General Description

LAN Connector LEDs

There are two LEDs for each of the two LAN ports (connectors) on the rear panel.

LINK/ACT LED

Each LINK/ACT LED indicates the status of the standard network port of the server.
While power is supplied to the server and HUB and the connection is correct, the LED is
on (green). The LED turns green and flashes while the network port is
transmitting/receiving data.

If the LED does not go on when the LINK state is placed, check if the network cable is in
normal state and if it is connected correctly. If the LED does not go on yet when the
network cable is normal, the network (LAN) controller may be faulty. In this case,
contact your service representative.

Speed LED

This LED indicates whether each of the network ports normally equipped with the server
is operated through the 1000BASE-T, 100BASE-TX or 10BASE-T network interface. If
the LED is lit amber, the network port is operated through 1000BASE-T. If the LED is
lit green, the network port is operated through 100BASE-TX. If the LED is off, the
network port is operated through 10BASE-T.

Speed LEDs

LINK/ACT LEDs

«
...
44
45
46
47
48
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

SUPERSERVER 5018D-MHR7N4P

Бренд: Supermicro Страницы: 126

SuperServer 5013C-MT

Бренд: Supero Страницы: 98

x3800 - System - 8865

Бренд: IBM Страницы: 104

Бренд: Rackable Systems Страницы: 4

Бренд: Sollae Systems Страницы: 45

Бренд: ANTAIRA Страницы: 2

Бренд: MISUMI Страницы: 18

SuperServer 6029U-TR25M

Бренд: Supermicro Страницы: 151

Бренд: Cisco Страницы: 2

Бренд: Acer Страницы: 52

Бренд: Acer Страницы: 94

Altos R700 Series

Бренд: Acer Страницы: 135

Бренд: Acer Страницы: 10

Бренд: Acer Страницы: 148

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 118

Бренд: Acer Страницы: 78

Altos G700 series

Бренд: Acer Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды