manualshive.com logo in svg

NEC Express5800/120Rh-2, Руководство пользователя

Поделиться
Скачать
NEC Express5800/120Rh-2 Скачать руководство пользователя страница 146

5-4  Installing the Operating System with Express Setup

Optional Board Supported by NEC EXPRESSBUILDER

NEC EXPRESSBUILDER CD-ROM attached to your system supports the following optional
boards;

NOTE:

 If you want to install the other boards by using a driver floppy

disk ("OEM-FD for Mass storage device"), except ones listed below,
see "Exceptional setup" and "Installing Optional Mass Storage Driver"
of "Configuration Diskette Creator" in Chapter 6.

„

 

Supporting installation of OS in NEC EXPRESSBUILDER

–

 

N8103-80F Disk Array Controller (SCSI 1ch)

–

 

N8103-81F Disk Array Controller (SCSI 2ch)

–

 

N8103-86 Disk Array Controller (0ch)

–

 

N8103-91 Disk array controller (Internal SAS HDD)

–

 

Adaptec HostRAID(SCSI) (Controller on the I/O board)

„

 

Other optional boards

–

 

N8103-56 SCSI Controller

–

 

N8103-65F SCSI Controller

–

 

N8103-75 SCSI Controller

–

 

N8103-95 SCSI Controller

–

 

N8190-126 SCSI Controller

[In case of use of N8103-91]

In use of N8103-91, please surely install Windows Server 2003 ServicePack 1 by
Windows Server 2003.

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды