NEC Express5800/120Rh-2 страница 298 Скачать руководство пользователя

Страница: 298 / 406

9-24 Upgrading Your Server

Installation

Take the following steps to install the CPU.

See the section "Preparing for Installation and Removal" described earlier to prepare.

Pull out the server from the rack.

Open the drive cover and logic cover.

Remove two screws securing the support arm.

Remove the support arm from the chassis.

NOTE:

When the support arm comes up, you may lose the screws.

Press firmly the support arm before removing the screws.

Remove the processor duct from the chassis.

Locate the CPU socket which you are going to install CPU.

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды