NEC Express5800/120Rh-2 Скачать руководство пользователя страница 91

Страница: 91 / 406

Setting Up Your Server 3-17

Device with the serial interface
(e.g., Management PC)

Keyboard

Mouse

Hub

(multiport repeater)

*1 Any USB keyboard and mouse are not supported.
*2 A leased line cannot be connected directly to this connector.

The console of a management PC can be connected to only serial port B. (BIOS setup required.)

*3 Use the provided branch cable.
*4 Connect the power cord to a circuit breaker of 15 A or less.
*5 Used exclusively with onboard SCSI connector.

USB device

FRONT

REAR

Device with the

SCSI interface

Device with the

serial interface

Finally connect the provided
power cord to the receptacle.

If connecting the server to UPS,
see the explanation below.

Display unit

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Бренды по названию

Популярные бренды