NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 76 / 406

background image

3-2 Setting Up Your Server

SETUP FLOW

Follow the flowchart below to set up the server.

Selecting the server site

Select a suitable site for the server. Assemble the 19-inch rack assembly.

Unpacking the system

Unpack the server and accessories from the chipping carton box.

Installing the server

Install the server into the rack assembly.

Connecting peripheral devices

Connect peripheral devices to the server.

Connecting the power cord

Connect the power cord to the server.

Turning on the server

Power on the server to start software setups. Setups depend on the optional internal
devices installed and the peripheral devices connected.

Installing the operating system

Install an operating system to the server. See Chapter 5.

Installing the utilities

Install the utilities in the provided NEC EXPRESSBUILDER CD-ROM.
See Chapter 6.

Making backup copies of system information

After all the system setup procedures are completed, make backup copies of system
information.
System information is required for recovering the server from the trouble or after
replacing the system board.

«
...
74
75
76
77
78
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Бренд: Lantronix Страницы: 10

Бренд: Lantronix Страницы: 17

Бренд: Lantronix Страницы: 109

Бренд: Lantronix Страницы: 24

Бренд: Lantronix Страницы: 29

Бренд: Lantronix Страницы: 2

Express5800/R310e-E4

Бренд: NEC Страницы: 86

FusionServer CH242 V5

Бренд: xFusion Digital Technologies Страницы: 61

Бренд: TP-Link Страницы: 16

Бренд: NTI Страницы: 35

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

Бренд: Speco Страницы: 28

Active Fabric Manager

Бренд: Dell Страницы: 44

Бренд: Dell Страницы: 120

Бренд: Dell Страницы: 76

Active Fabric Manager

Бренд: Dell Страницы: 127

Бренд: Dell Страницы: 122

DR4000 Restore Manager

Бренд: Dell Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды