manualshive.com logo in svg

NEC Express5800/120Rh-2, Руководство пользователя

Поделиться
Скачать
NEC Express5800/120Rh-2 Скачать руководство пользователя страница 68

2-36  General Description

Identification of Servers (UID Switch)

An "UID (Unit ID) LED" is provided on the front panel and rear panel.    If more than one server is
mounted in a single rack, the LED identifies the server you are going to maintain.

The UID LED goes on when the UID (Unit ID) switch on the front panel is pressed.    It goes off
when the switch is pressed again.

Maintenance from the rear of the rack has to be carried out in a dark, narrow space.    The interface
cable of a server or power supply unit in normal state may be disconnected by accident in this
situation.    To prevent this problem, you should start maintenance after confirming the target server
by using the UID switch.

FRONT

REAR

UID

switch

UID LED

UID switch

UID LED

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды