NEC Express5800/120Rh-2 Скачать руководство пользователя

Страница: 361 / 406

Installing Windows Server 2003 x64 Editions D-15

Graphics Accelerator Driver

Standard graphics accelerator drivers that are mounted will be installed automatically.

The following is the procedure when it is necessary to install manually.

If you want to utilize optional Graphics Accelerator Driver board, follow the document attached to
the board to install the driver.

* For the graphics accelerator driver for Windows Server 2003 x64 Editions, the use of a remote

KVM console that installs the advanced N8115-02 remote management card is supported by the
standard. A special driver need not be installed.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Click Start menu, point to [Programs], [Accessories] and click [Windows Explorer]

Run "SETUP.EXE" in the following directory.

<CD-ROM Drive Letter>:\WINNT\W2K3AMD\VIDEO\SETUP.EXE

Follow the message to continue the installation.

Remove the NEC EXPRESSBUILDER CD-ROM from the CD-ROM drive, follow the
direction on the screen and restart the system.

Installing SCSI Controller Driver (N8103-56/-75/-95/N8190-126)

If you utilize SCSI controller driver (N8103-56/-75/-95/N8190-126), update your system with NEC
EXPRESSBUILDER CD-ROM attached to your system.

The SCSI controller driver will be installed automatically.

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды