NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 79 / 406

background image

Setting Up Your Server 3-5

UNPACKING THE SYSTEM

When you receive your system, inspect the shipping containers prior to unpacking. If the shipping
boxes are damaged, note the damage, and if possible, photograph it for reference. After removing
the contents of the containers, keep the cartons and the packing materials. If the contents appear
damaged when you unpack the boxes, file a damage claim with the carrier immediately.

INSTALLING THE SERVER

This subsection provides the instructions for the rack-mount server unit into a standard EIA 19-inch
rack cabinet.

Also this subsection describes the removal procedures for the rack-mount server unit from the 19-
inch rack cabinet.

WARNING

Observe the following instructions to use the server safely. Failure to follow
these instructions may result in death or serious personal injury. See pages 1-
3 to 1-8 for details.

Do not use any rack which does not conform to the relevant standard.

Disconnect the power cord(s) before installing or removing the server.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-8 for details.

Do not leave more than one device being pulled out from the rack.

Do not lift the server only by a single person.

Always install the server in the specified place.

Do not install the server on the rack leaving the cover removed.

Do not pinch your finger with mechanical components.

«
...
77
78
79
80
81
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Бренд: A10 Networks Страницы: 17

Бренд: Lantronix Страницы: 299

Бренд: Sun Microsystems Страницы: 128

Бренд: Avaya Страницы: 19

Бренд: 3onedata Страницы: 4

Бренд: SMC Sierra Monitor Страницы: 42

UniServer E3200 G3

Бренд: H3C Страницы: 401

88743BU - System x3950 E

Бренд: IBM Страницы: 426

Бренд: TYAN Страницы: 77

Бренд: IBM Страницы: 90

Advanced Office-in-a-Box

Бренд: Enconnex Страницы: 40

Бренд: Eelectron Страницы: 42

Бренд: Eelectron Страницы: 113

Бренд: TAG Страницы: 72

IXG CloudBridge

Бренд: evertz Страницы: 52

Бренд: 3onedata Страницы: 20

Бренд: D-Link Страницы: 146

P400u - 32371 NAS 7200 RPM 160 GB Server

Бренд: Iomega Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды