NEC Express5800/120Rh-2 Скачать руководство пользователя

Страница: 164 / 406

5-22 Installing the Operating System with Express Setup

Graphics Accelerator Driver

Standard graphics accelerator drivers that are mounted will be installed automatically.

The following is the procedure when it is necessary to install manually.

If you want to utilize optional Graphics Accelerator Driver board, follow the document attached to
the board to install the driver.

* For the graphics accelerator driver, the use of a remote KVM console that installs the advanced

N8115-02 remote management card is supported by the standard.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Click Start menu, point to [Programs], [Accessories] and click [Windows Explorer]

Run "SETUP.EXE" in the following directory.

<CD-ROM Drive Letter>:\WINNT\DOTNET\VIDEO\SETUP.EXE

Follow the message to continue the installation.

Remove the NEC EXPRESSBUILDER CD-ROM from the CD-ROM drive, follow the
direction on the screen and restart the system.

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды

NEC Express5800/120Rh-2, Руководство пользователя

Результаты поиска

Содержание Express5800/120Rh-2

Отзывы:

Похожие инструкции для Express5800/120Rh-2

Бренды по названию

Популярные бренды