NEC Express5800/120Rh-2 Скачать руководство пользователя | Manualshive

Страница: 47 / 406

background image

General Description 2-15

AC POWER LED

There is an AC POWER LED for the power supply unit on the rear. The LED turns green and
flashes when the power supply unit receives AC power from the power cord, which is connected to
the AC inlet.

The LED turns green when the server power switch is turned on. If the LED does not go on when
the server power switch is turned on or if it turns or blinks amber, the power supply unit is probably
faulty. In this case, contact your service representative to replace the power supply unit.

NOTE:

If one power supply unit fails while an optional power supply

is mounted, the system can continue operation with the other power
supply unit. (Redundant function) The failing power supply unit can
be replaced in hot swap mode (with the power on) without the system
being stopped.

AC inlet

Power supply
slot 1

Power supply
slot 2

AC POWER LED

«
...
45
46
47
48
49
...
»

Содержание Express5800/120Rh-2























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express5800/120Rh-2

Network Space MAX

Бренд: LaCie Страницы: 2

Бренд: Z Microsystems Страницы: 17

TJA670 domovea Basic

Бренд: hager Страницы: 36

Бренд: Kontron Страницы: 110

Бренд: ImageTech Страницы: 44

RS/6000 44P Series 270

Бренд: IBM Страницы: 346

ProLiant ML350 G3

Бренд: HP Страницы: 44

ProLiant ML310e Gen8 v2

Бренд: HP Страницы: 43

ProLiant ML330 Generation 3

Бренд: HP Страницы: 34

PROLIANT ML350 G6

Бренд: HP Страницы: 145

ProLiant ML350 Gen9

Бренд: HP Страницы: 171

PROLIANT ML350 G6

Бренд: HP Страницы: 103

PROLIANT ML330 G6

Бренд: HP Страницы: 137

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

IP-DECT SERVER 6500

Бренд: SpectraLink Страницы: 2

TS-269L TurboNAS

Бренд: QNAP Страницы: 6

Бренд: EVS Страницы: 118

Бренд: Viavi Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды