manualshive.com logo in svg

Motortech DetCon series, Руководство по эксплуатации

Поделиться
Скачать
Motortech DetCon series Скачать руководство пользователя страница 49

5 Installation Instructions 

 

Rev. 02/2019 

49 

5.3 

 

Mounting the Detonation Sensors 

 

Danger of explosion! 

Only use the detonation sensor approved by MOTORTECH and the required 
number of blocking capacitor boards for operation in hazardous areas. 

  

P/N 

Description 

43.20.001 

Detonation sensor without sensor lead, two-pole 

43.30.004-60 

Detonation sensor lead, 18 m (59.06 ft) 

43.20.029 

Blocking capacitor board (ATEX) 

 

        

 

Use MOTORTECH detonation sensors 

DetCon detonation controller systems are parameterized for operation with 
MOTORTECH detonation sensors (piezoelectric acceleration transducers). 
The use of other sensors entails a new calibration of the engine. 

   

 

Observe the instructions of the engine manufacturer 

The following mounting instructions are for orientation only. In any case, 
observe the instructions of the respective engine manufacturer for the 
installation of detonation sensors and the installation of detonation 
controllers. 

 Dimensions of the Sensor 

 

Содержание DetCon series



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды