manualshive.com logo in svg

Motortech DetCon series, Руководство по эксплуатации

Поделиться
Скачать
Motortech DetCon series Скачать руководство пользователя страница 29

4 Product Description 

 

Rev. 02/2019 

29 

4.1.3

 

Warning Notices on the Device 

The safety instructions on the device or on the enclosure are valid for the DetCon and all 
connected components. 

  

Variant 

Information text 

ATEX and CSA

 

WARNING – EXPLOSION HAZARD – Substitution of components may 
impair suitability for Class I, Division 2. Do not disconnect equipment 
unless power has been switched off or the area is known to be non-
hazardous. 

All 

 

WARNING! Read and understand the installation and operation manuals 
prior to installing or making any adjustments. 

ATEX

 

EXPLOSION HAZARD – Do not open enclosure or disconnect while circuit 
is live unless area is known to be non-hazardous. For wiring details 
please refer to operation manual. 

ATEX

 

The device must be installed and operated only in an environment that 
ensures a pollution degree 2 (or better) according to IEC/EN 60664-1. 

All 

 

CAUTION – Do not pressure wash this ignition module. Damage to 
electronic components may result.  

CSA

 

EXPLOSION HAZARD – Do not disconnect while circuit is live unless area 
is known to be non-hazardous. For wiring details please refer to 
operation manual 

  

 

Содержание DetCon series



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды