Motortech DetCon series Скачать руководство пользователя страница 38

Страница: 38 / 90

4 Product Description

Rev. 02/2019

DetCon20 – Ports/Connections and LEDs

Labeling

Function

LOAD RESISTANCE

Jumper which must be removed if no ignition sensor unit (ISU) is
used (when using a camshaft sensor or MOTORTECH ignition
controllers with ASO output)

Sensor A-B (DetCon2)
Sensor 1-20
(DetCon20)

Connections of the detonation sensors (A=white, B=brown,
S=shield) (see

Wiring of the Detonation Sensors

on page 57)

Timing1, Timing2,
Shield 0 V, +24 V

Connections for the ignition sensor unit (ISU) or the camshaft
sensor (see

Wiring of the Ignition Sensor Unit (ISU)

on page 59 or

Wiring of the Camshaft Sensor (for Diesel and Pilot Injection Engines
Only)

on page 62)

IGNITION PULSE (LED)

This LED flashes when an ignition pulse is transmitted to the
DetCon.

Содержание DetCon series



























































































Результаты поиска

Содержание DetCon series

Отзывы:

Бренды по названию

Популярные бренды

Motortech DetCon series, Руководство по эксплуатации

Результаты поиска

Содержание DetCon series

Отзывы:

Бренды по названию

Популярные бренды