manualshive.com logo in svg

Motortech DetCon series, Руководство по эксплуатации

Поделиться
Скачать
Motortech DetCon series Скачать руководство пользователя страница 19

3 Intended Use 

 

Rev. 02/2019 

19 

Instructions for handling the DetCon20 detonation controller in hazardous areas 
 

 

Danger of explosion! 

Only use the detonation sensor approved by MOTORTECH and the required 
number of blocking capacitor boards for operation in hazardous areas. 

  

P/N 

Description 

43.20.001 

Detonation sensor without sensor lead, two-pole 

43.30.004-60 

Detonation sensor lead, 18 m (59.06 ft) 

43.20.029 

Blocking capacitor board (ATEX) 

 

        

 

Danger of explosion! 

The USB interface may only be used in a non-hazardous atmosphere. There 
is a danger of sparking. 

          

 

Sealing of the enclosure to the enclosure cover  

The enclosure is sealed against the enclosure cover by a foamed silicone 
seal. The overlapping of the foam bead (start point/end point) of the seal 
cannot be produced without any joints due to the material, but has no 
influence on the specified IP protection class. 

           

 

Use MOTORTECH detonation sensors 

DetCon detonation controller systems are parameterized for operation with 
MOTORTECH detonation sensors (piezoelectric acceleration transducers). 
The use of other sensors entails a new calibration of the engine. 

  

 

 

Содержание DetCon series



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды