Motortech DetCon series Скачать руководство пользователя страница 47

Страница: 47 / 90

5 Installation Instructions

Rev. 02/2019

Type examination certificate

All lead bushings and cable bushings must have a separate EC type
examination certificate.

Dummy plugs used require a separate EC type examination certificate.

Operational safety

All lead bushings must be mounted with a metal locknut.

When using lead bushings with strain relief and bending protection, the
number of possible standard lead glands is reduced.

Mixed fitting of lead bushings is possible. Areas for intrinsically safe
circuits must be marked separately.

Unused openings for lead bushings must be closed with blind plugs made
of cold impact resistant plastic or metal.

The lead bushings must be mounted in such a way that independent
loosening is prevented and permanent sealing of the lead and lead entry
points can be guaranteed. Lead ties are used for lead fixing.

The spacing of the lead bushings must be selected so that a torque wrench
can be used to tighten the lead bushings and cap nuts. .

Содержание DetCon series



























































































Результаты поиска

Содержание DetCon series

Отзывы:

Бренды по названию

Популярные бренды

Motortech DetCon series, Руководство по эксплуатации

Результаты поиска

Содержание DetCon series

Отзывы:

Бренды по названию

Популярные бренды