Moog DigiPack 2 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 87

background image

© MOOG 2010

This document is subject to MOOG INTELLECTUAL AND PROPRIETARY INFORMATION LEGEND . The details are on page II.

64

MRJ04410

2-4-5.

F4: Monitor Mode

Mode obtained by pressing the F4 key.

Display

Available  at  all  times.  But  not  available  to  change  manual
mode when manufacturing containers

Manual Mode is used to display and/or control the positions
of  the  tooling  actuator  (DCDT)  and  the  value  of  the  ser-
vovalve input current as well as the Output ON/OFF func-
tions. Auto Mode ONLY displays the above information.

Commands

The Cursor is used to move to the various commands only
in  MANUAL  mode.  The  Set  Key  is  inactive.  The  displayed
values reflect the actual positions or servovalve current. (or
Spool position in EFB mode)

Output

There are 7 output commands which may be changed with the  Entry Knob. Counter-clockwise rotation
produces a 0 (OFF) and Clockwise rotation a 1 (ON).

The functions controlled are: (1) End of Filling; (2) End of Extrusion; (3) Point out; (4) Production; (5) End of
Start slope; (6) Ready; (7) Alarm.

Input

There are 10 input commands to monitoring the following functions: (1) Start, (2) Die gap; (3) Reset; (4)
Stop; (5) Function 1; (6) Function 2; (7) Function 3; (8) Function 4, (9) Start Slope, (10) Servo off.

Core check

When the display Cursor points to “Core check”, it is possible to control the tooling position in closed loop
using the Entry Knob between 0 to over 3276.7%. (100% = Span position)

Open command

When the display Cursor points to “Open command”, it is possible to control the value of the servovalve
input current with the Entry Knob.

Figure 2-26 F4: Monitor Mode Screen

«
...
69
70
71
72
73
...
»

Содержание DigiPack 2
























































































Отзывы:

Нет отзывов

Похожие инструкции для DigiPack 2

Бренд: S&C Страницы: 40

Бренд: DAV TECH Страницы: 10

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: Multi-Clean Страницы: 4

Бренд: Primo Water Страницы: 10

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

NuMicro M252 Series

Бренд: Nuvoton Страницы: 38

Бренд: Blucave Страницы: 2

Бренд: K&K Страницы: 10

MorphoAccess VP MD

Бренд: Idemia Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды