Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 308

Страница: 308 / 366

Diagnosing Problems

Boot Sequence

Phone Display

The internal DHCP server provides one of these

options:

An external DHCP server provides one of these options:

(where n is the number of the sub-option if encapsulation

is used for the option.)

Using option 125

Using option 43

Using option 128+

---------------------

Using option 125:n

Using option 43:n

The DHCP server on the default VLAN responds with

an Offer. If Option 43 or 125 (or option 130 prior to 3300

Release 7.0) is not properly set on the server, the set

awaits further Offers (n is offer number).

DHCP: Offer n Rej

Booting: 04.02.01.06

---------------

DHCP: Offer n Acc

Booting: 04.02.01.06

The set replies with a Request and the server replies

with an Acknowledgement.

DHCP: Ack

Booting: 04.02.01.06

If the data in the Ack does not contain a VLAN ID and

a packet Priority value, the set retains DHCP data, jumps

Step 10

If the data included in the Ack does include a VLAN

ID and packet Priority value, the set discards DHCP data

and sends an untagged Release.

DHCP: Releasing

Booting: 04.02.01.06

---------------------

Vlan x Priority x

Booting: 04.02.01.06

Document Version 1.0
Troubleshooting Guide

302

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды