Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 212

Страница: 212 / 366

Tools and Embedded Applications

Symptom

Probable Cause

Corrective Action

ACD RAD ports don’t play

for incoming calls on SIP

Trunks

Programming error.

In the SIP peer profile,

make sure that “Suppress

Use of SDP Inactive Media

Streams” is set to NO.

Refer to Mitel

Knowledge Base article

07-5157-00018 for more

information.

The “Generic Group Alert”

key does not work.

The Generic Group Alert

function is intended to

display single queue

status when an agent logs

in. If the agent belongs

to multiple groups, the

function does not know

which group to display and

will not work.

To display the queue

status for each group that

includes that particular

agent, program a “Specific

Group Alert” key for each

group.

7.2 Hot Desking

Table 35: Hot Desk Troubleshooting

Symptom

Probable Cause

Corrective Action

When a hot desk user

attempts to log in, the

following error message

appears on the display of

the IP phone:

“Error: feature failure”.

Both the hot desk enabled

set and the hot desk user

are local on the 3300 ICP.

The PBX Number and the

Cluster Element ID that are

programmed for the 3300

ICP do not match.

Ensure that the PBX

Number in the ICP/PBX

Networking form matches

the Cluster Element ID in

the Cluster Elements form.

Document Version 1.0
Troubleshooting Guide

206

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды