Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 7

Страница: 7 / 366

Introduction

This chapter contains the following sections:

•

Supporting Documentation

•

Resolving Technical Issues

•

TSN Your Technical Support Network

•

Self Help Solutions

•

Accessing Product Support

•

Returning Faulty Hardware

About this Guide

This guide provides troubleshooting information for the Mitel

3300 IP Communications

Platform (ICP). This guide is intended for use by Mitel certified 3300 ICP technicians.

The troubleshooting information has been grouped by topic (Initial Setup, System Features,

Devices, and so forth) and then organized into tables using the following structure:

•

Symptom,

•

Probable Cause, and

•

Corrective Action.

To locate help on a specific problem

•

Use the Adobe Acrobat search functionality to search for key words associated with the

problem symptoms, or

•

Go to the table that contains troubleshooting information related to the problem and scan

the symptoms column for a possible match.

Note

The AX Controller will be supported in MiVoice Business Release 9.1 and later

versions.

What’s New in this Document

This section describes changes in this document due to new and changed functionality in

MiVoice Business Release 9.4 SP1. The changes are summarized in the following table.

Document Version 1.0
Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды