Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 27

Страница: 27 / 366

Initial Setup

This chapter contains the following sections:

•

Licensing

Initial Setup Troubleshooting Tips

•

Refer to the Technician's Handbook for instructions on how to install and set up a 3300 ICP

controller.

•

For hardware related issues, also see

Controllers

Table 4: General Controller Setup Troubleshooting

Symptom

Possible Cause

Corrective Action

Unable to access the

console screen.

You are replacing an

existing 3300 ICP

controller with another

controller, and trying to

use the same system

IP address for the new

controller from a PC on a

different subnet.

Initially, you can only connect to the

controller from the local subnet.

Before you can connect to the

new controller from other subnets,

you must manually clear the

router ARP cache or wait until the

router ARP cache is automatically

updated. Refer to the latest 3300

ICP Release Notes for instructions.

Power cable is not

securely plugged into the

controller and/or power

source.

Ensure power cable connections

are secure.

Controller not powering

up.

The power switch or both

power switches on a

redundant power supply

controller are not on.

Ensure power switch or both power

switches on a redundant power

supply controller are turned on.

Document Version 1.0
Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды