Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 180

Страница: 180 / 366

Trunking

Symptom

Probable Cause

Corrective Action

Embedded PRI calls

fail and all Status LEDs

on the Dual T1/E1

Framer are OFF.

Configuration.

Verify that embedded PRI is

programmed properly in the

following forms (see also Program

Embedded PRI/Q.SIG in the Online

Help):

•

Controller Module Configuration

•

Dual T1/E1 Framer

Configuration

•

Link Descriptor Assignment

•

Digital Link Assignment

After the Digital Links form is

completed, the T1/E1 Framer

status LEDs should come on. This

takes about 15 seconds.

Embedded PRI Links

are “not seizable”,

Status LEDs show

RED alarm.

Configuration or wiring. Ensure that the ISDN cable is

plugged into the correct RJ-45 port

on the Dual T1/E1 MMC. Verify that

the ISDN cable is correctly wired.

Change the “Termination

Mode” setting in the Digital Link

Descriptors form - either LT or

NT. This change takes about 30

seconds to take effect.

Embedded PRI links

are “not seizable”,

Status LEDs show

flashing GREEN.

Configuration.

Verify the “Network Side/QSIG

Master” setting in the ISDN

Protocol form. Check the “Inverted

D-Channel” setting in the Digital

Link Descriptors form - normally it is

set to “No”. Each of these changes

takes approximately 30 seconds.

Document Version 1.0
Troubleshooting Guide

174

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды