Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 20

Страница: 20 / 366

Introduction

Required Information

Details

Trunking

What types of trunks (PRI, BRI, LS,

DID, XNET/IP, and so forth) are on the

system?

How are trunk groups set up?

How are the LS trunk descriptors

programmed?

FAX Support

What type of fax machines are installed?

What is their make and model number?

Are you using T.38 for faxing? Do the

fax calls go over any IP connection, IP

trunks or SIP?

Contact telephone number and e-mail

address

Be prepared to provide the Mitel

Technical Support technician with a

telephone number and e-mail address

so that the technician can contact you

or provide your contact number to other

support specialists. If your call concerns

an emergency problem, ensure that you

can be reached at the telephone number

at any time. Don’t provide a number that

will forward the technician to voice mail.

Don’t provide a cell phone number that is

likely to be unreachable (out-of-range).

If the problem is with an IP Phone, have you collected the following information?

Document Version 1.0
Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды