Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 107

Страница: 107 / 366

Hardware

Symptom

Possible Cause

Corrective Action

Broken Audio,

intermittent

Layer 2 Switch ports

configured incorrectly.

In the Layer 2 Switch form of

the System Administration Tool,

configure all L2 ports in the voice

path with the same settings. The

recommended settings for the

“Duplex Mode” field and the “Flow

Control” field is “Auto”.

If the network requires fixed

settings, use the following:

•

State - Enabled

•

Speed - 100 Mb

•

Duplex Mode - Full DX

•

Flow Control - Enabled

•

Voice VLAN - Tagged

If you change these fields to fixed

settings, you must also set the IP

phones to use the fixed settings.

You change the IP phone settings

through the Configuration menu.

See

Access Configuration Menu on

Single-Mode IP Phones

In the Configuration menu, select

Hardware Config?

and then select

Modify Port Setting

and modify

the settings.

Echo occurring

between IP

Phones and

TDM Phones

Handsfree mode is used.

Check if far end is using handsfree.

Switch to handset mode to see if this

corrects it, or lower the volume in

handsfree mode.

Document Version 1.0

101

Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды