Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 189

Страница: 189 / 366

Trunking

Symptom

Probable Cause

Corrective Action

Incoming calls fail.

Faulty configuration of trunk

Forms.

Verify in the Trunk

Attributes form that there

is an Answer Point setup

for non-DDI trunks for Day

and Night services.

For dial in trunks, the “Dial

In Trunks Incoming Digit

Modification – Absorb” is

not left blank and that the

“Dial In Trunks Incoming

Digit Modification – Insert”

is set appropriately for dial

in trunks.

All calls on a link fail.

Faulty cable connections,

cable, or card.

Check the status of the

link by using the DTSTAT

READ PLID maintenance

command.

Check the cabling and

cable connections. Test

with a back-to-back cable

to prove the card.

Replace faulty cable or

card.

Only some calls on a

link fail.

Configuration errors in

programming

•

ARS programming error

•

Digit conflict

•

Interconnect Restriction

preventing call

•

Far end fault/programming

Correct programming

through System

Administration Tool.

Document Version 1.0

183

Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды