Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 100

Страница: 100 / 366

Hardware

Error Message

on Display

Possible

Cause

Corrective Action

The Layer 2

switch port for the

phone interface

is shut down or

not configured

properly.

Check the Layer 2 switch and ensure that

the port is not shut down (see “Network

Configuration Examples” in the “Typical

Network Configurations” chapter of

the

Technician’s Handbook

for more

information).

For a Cisco Layer 2 switch: verify that this

is a trunk port with Dot1q encapsulation,

and ensure this trunk port allows both

native and voice LAN to pass through.

For an HP Layer 2 switch: verify that Native

Lan is untagged and Voice Lan is tagged.

TFTP Fail

( Remote

IP phone

with statically

programmed IP

address cannot

access MN3300

across WAN).

The Layer 2

switch port for

router interface

is shut down or

not configured

properly.

Verify which configuration you have (see

“Network Configuration Examples” in the

“Typical Network Configurations” chapter

of the Technician’s Handbook for more

information).

Ensure the port(s) on both sides (Layer 2

switch and router) are not shut down.

If there is physical interface on the router

for each VLAN, make sure that the Layer

2 switch is set to access the port for the

corresponding VLAN/subnet correctly; OR

If this is a router on a switch, verify that this

is a trunk port on L2 switch, and ensure

this trunk port allows both native and voice

LAN to pass through.

On the router's sub-interface, verify that

the proper VLAN is associated to the sub-

interface (see “Network Configuration

Examples” in the “Typical Network

Configurations” chapter of the

Technician’s

Handbook

for more information).

Document Version 1.0
Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды