Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 222

Страница: 222 / 366

Tools and Embedded Applications

Symptom

Probable Cause

Corrective Action

Users suddenly cannot

access Visual Voice Mail.

Range programming in

progress.

While an administrator

is using range

programming in the

System Administration

Tool to modify the system

database, users will be

unable to access Visual

Voice Mail. Perform range

programming outside of

regular business hours.

Also if Audit/ Backup/

Restore in progress. User

can not login into VVM.

Unable to add or edit

mailboxes. Attempts result

in an error message, “A

Voice Mail Server Name for

a local mailbox must match

System Name.”

Voice mail server host

name doesn’t match 3300

ICP system name.

The host name of the

voice mail server in the

VM Network Servers form

must match the entry in the

Name field in the Network

Elements form. To correct

the problem, change the

Name field in the Network

Elements form to match the

voice mail server name.

Embedded Voice Mail

cannot transfer or page

externally (fails or rings

only once).

Supervised Transfer is

enabled, and the Transfer

Ringback Timeout is set to

default 17 sec.

In the VM Options form,

disable the “Enable

Supervised Transfer".

However, the default

Transfer Ringback timeout

is 17 sec now.

Document Version 1.0
Troubleshooting Guide

216

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды