Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 261

Страница: 261 / 366

Voice Networking

Symptom

Possible Cause

Corrective Action

The shared data has

different default settings

because the system

Country variants (set in

the License and Option

Selection form) are

different on the master and

remote elements.

Accept the values using the

Force Change option, or do

not share this data.

By default, user and device

data is not shared. You

must first specify the

resilient user and device

data that you want to be

shared with the secondary

elements.

Specify the resilient user

and device data that you

want to be shared with the

secondary elements.

Resilient user and device

data is not being shared

after you upgraded the

controllers to 3300 Release

7.0 software or higher.

Version of the remote peer

has not been updated on

the local controller

Perform a synchronization

from the local element to

the remote peer.

Data for some fields are

not being shared. Upgrade

the controller to the higher

software level.

If a 3300 Release 7.0

or later SDS-enabled

controller is communicating

with a 3300 Release 6.x

SDS-enabled controller,

only the forms that are

supported by the Release

6.x SDS will be shared.

User and device resiliency

data will not be shared to

the Release 6.x controller.

Upgrade the controller to

the higher software level.

Document Version 1.0

255

Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды