Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 262

Страница: 262 / 366

Voice Networking

Symptom

Possible Cause

Corrective Action

In the SDS Form Sharing

form, some record

restrictions appear as “Not

supported in this Release”.

If you share the SDS Form

Sharing form from a 3300

Release 7.0 controller to

a controller running an

earlier software release

(from 3300 Release 6.1

UR2 to pre-Release 7.0)

any new Release 7.0 fields

that are not supported on

the older software release

are displayed as “Not

supported in this Release”

on the controller with the

older software.

Upgrade the controller to

the higher software level.

In the SDS Form Sharing

form of a controller that

has pre- 3300 Release 6.1

UR2 software, some record

restrictions are incorrectly

displayed as “Account

Code”.

If you share the SDS

Form Sharing form from

a 3300 Release 7.0 or

later controller among

controllers that have pre-

3300 Release 6.1 UR2

software, restrictions

in the Feature Access

Codes form may appear

incorrectly. If you restrict

sharing of the Call Park

and Call Park Retrieve

fields from the 3300

Release 7.0 system, these

restrictions are incorrectly

displayed as “Account

Code” on the controllers

with the older software.

Upgrade the controller to

the higher software level.

Errors show that data

has been distributed to a

network element in a way

that is not consistent with

the data in the Remote

Directory Number form.

An administrator made

an incorrect entry to

the Remote Directory

Number form at an element

somewhere in the network

and the change has been

propagated by SDS.

Delete the inconsistent

record from the Remote

Directory Number

form, and reprogram it

appropriately.

Document Version 1.0
Troubleshooting Guide

256

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды