Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 301

Страница: 301 / 366

Diagnosing Problems

Note

Speed and duplex mode are not configurable on the 5560 IPT.

To manually configure speed and duplex mode:

Access the Configuration Menu (see

Access Configuration Menu on Single Mode IP

Phones

Press

until HARDWARE CONFIG? appears, and then press

Yes

. MODIFY

SETTINGS? appears.

Do one of the following and then reboot the phone:

•

To modify the current hardware components, press

Yes

, and then follow the

prompts to modify each setting and store the changes.

•

To reset the factory defaults, press

Default

, and then follow the prompts to set and

store the factory defaults.

To exit the current menu without a reboot:

•

To return to the main menu, press

Yes

at EXIT MENU?

•

To return to the default display, press

Superkey

Setting the Phone Mode

You can program the 5215 or 5220 IP Phone (Dual Mode) to use MiNET or to work

remotely using either SIP or Teleworker Solution (6010).

For SIP configuration information, refer to the 5207/5215/5220 IP Phone Installation

Guide (56006499, Rev A) packaged with the phone, and to the 5215/5220 IP Phone SIP

User Guide available at www.mitel.com.

Using Tools and Features

•

Erasing the Registration PIN

•

Pinging IP Addresses

•

Conducting a DHCP Trace

•

Configuring Video Conferencing Parameters

•

Restoring Factory Default Settings

Erasing the Registration PIN

Document Version 1.0

295

Troubleshooting Guide

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды