© 2014 MIMAKI ENGINEERING CO.,LTD.
7.1.2
P.5
7.1.2 List of Error Messages
1
2
3
4
5
6
7
8
48
ERROR 50f
L-SCALE BLACK
Liner Scale error
1. Check the assembly position of Linear Scale and
Encoder PCB Assy..
2. Check Linear Scale (scratches or dirtiness or so.)
3. Replace the Linear Scale with a new one.
4. Replace the Encoder PCB Assy. with a new one.
(Refer to 6.4.8)
49
ERROR 529
LEnc.Count HPC[____]
Difference of linear scale value (HPC1 and
HPC2)
50
ERROR 52a
LEnc.Count HDC[____]
Difference of linear scale value (HDC and
HPC2)
51
ERROR 516
MEDIA SET POSITION L
ERROR 516
MEDIA SET POSITION R
The media is set outside the range.
1. Check the media setting position.
2. Perform cleaning of the media width sensor.
3. Execute [#TEST PAPER SENSOR].
52
ERROR 528
PUMP MOTOR SENSOR
Detecting error of pump sensor
1. Perform [#TEST][SENSOR][PUMP MOTOR], and con-
firm pump operation and sensor reaction by pressing
[FUNC] key.
2. Replace the sensor.
3. Replace the suction pump.
53
ERROR 602
CARTRIDGE END
Ink end
(Non of printing, ink use-up cleaning is only
allowed.)
(When the message is still displayed even after a new Ink
Cartridge or an empty Ink Cartridge is charged;)
1.
Perform and confirm [#TEST][SENSOR][CartridgeSen-
sor]. (The number correspond to the cartridge number.)
2. Check the peripheral and the assembly of near end sensor.
3. Check the connection of theD contact PCB Assy. and near
end sensor.
4. Replace the cartridge.
5. Replace the ID contact PCB Assy. and near end sensor with
new one.
6. Replace the CART IO PCB with a new one.
7. Replace the MAIN PCB with a new one.
(Refer to
3.3.1)
54
ERROR 608
WRONG INK IC
IC chip of Ink cartridge unreadable property.
1. Check the attached status of the chip.
2. Perform and confirm [#TEST][CHECK INK IC].
3. Replace the ID contact PCB Assy. with new one.
55
ERROR 612
INK LVL LOW
When 600ml cartridge is used,
ink amount of the cartridge is less than 60ml.
1. Register weight of the cartridge.
2. Replace the cartridge and ink IC with a new one.
3. Perform and confirm [#TEST][CHECK INK IC].
4. Check the connection of theD contact PCB Assy.
5. Replace the ID contact PCB Assy. with new one.
6. Replace the CART IO PCB with a new one.
56
ERROR 613
INK LVL END
When 600ml cartridge is used,
ink amount of the cartridge is less than 25ml.
57
ERROR 614
Preservation Failure
When 600ml cartridge is used, writing to the
IC chip is failed at the time of weight
registration.
1. Replace the cartridge.
2. Perform and confirm [#TEST][CHECK INK IC].
3. Check the connection of theD contact PCB Assy.
4. Replace the ID contact PCB Assy. with new one.
5. Replace the CART IO PCB with a new one.
58
ERROR 627
RE-INSERT CARTRIDGE
The cartridge has not been set for a certain
amount of time.
Set the cartridge.
1. Check that the cartridge has been inserted correctly.
2. Check the sensor operation with
[#TEST][SENSOR][CartridgeSensor].
59
ERROR 628
WRONG INK CARTRIDGE
An error occurred in the IC chip information of
the ink cartridge.
The chip was used too much (exceeding the specified times).
1. Check whether the chip was also replaced when the pack
was replaced.
2. Check the W ink nozzle clogging and resolve it.
3. Replace the IC chip with new one.
List of Error Messages (5/7)
No.
LCD
Cause
List of Countermeasures
R.1.0
MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model
JV300-130/160
Issued 2014.05.30 Revised
F/W ver
1.10
Remark
1.0
Rev.
