Milnor E-P Plus Скачать руководство пользователя страница 4

Страница: 4 / 92

Pellerin Milnor Corporation

2.3.3.4 Create a New Formula................................................................................24
2.3.3.5 Delete an Existing Formula ........................................................................24
2.3.3.6 Change an Existing Formula ......................................................................25

2.3.3.6.1 How to Insert or Delete a Step in an Existing Formula...................25

2.3.3.6.1.1 Inserting a Step .....................................................................25
2.3.3.6.1.2 Deleting a Step .....................................................................25

2.3.3.6.2 The Step Decisions ..........................................................................26

2.3.3.6.2.1 How to Modulate Water Valves to Regulate Incoming

Water Temperature .................................................................29

2.3.4 Configure the Control (Option 2) ..........................................................................40

2.3.4.1 Moving Forward and Backward in

Configure

..........................................41

2.3.4.2 The Configure Decisions ............................................................................41

2.3.5 Restoring the Standard Formulas ..........................................................................45

2.3.5.1 Chart 1: Restore Standard Formulas (Part A).............................................45
2.3.5.2 Part B ..........................................................................................................46
2.3.5.3 Part C ..........................................................................................................46
2.3.5.4 Restoring the Standard Formulas on Models Employing the Milnor

E-P Plus

and E-P Express

Controller .................................................47

2.3.6 Data Transfer (Option 4) .......................................................................................48

2.3.6.1 Establishing the Required Connections......................................................49
2.3.6.2 Saving Data from the Machine to the Storage Device or a Second

Machine ..................................................................................................50

2.3.6.3 Restoring Saved Data to the Machine from the Storage Device or An-

other Machine .........................................................................................52

3 Operating .....................................................................................................................................55

3.1 Running a Formula ..........................................................................................................55

3.1.1 Applying Power.....................................................................................................55
3.1.2 Selecting and Starting the Formula .......................................................................55

3.2 How to Use and Erase the Formula Counter ...................................................................60

4 Troubleshooting...........................................................................................................................61

4.1 The E-P Plus

Manual Menu ..........................................................................................61

4.1.1 The

Manual Menu

................................................................................................61

4.1.1.1 Components ................................................................................................61
4.1.1.2 How to Access the

Manual Menu

............................................................61

4.1.1.3 How to Return to the

Run Mode

from the

Manual Menu

.......................62

4.1.6.1 Testing the Pressure Transducer Circuit .....................................................70

Contents

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 4 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: