Milnor E-P Plus Скачать руководство пользователя страница 29

Страница: 29 / 92

Pellerin Milnor Corporation

2.3.3.3

Moving Forward and Backward through Steps and Decisions

BNCJUP03.C04 0000191931 C.2 D.2 B.3 1/2/20 1:16 PM Released

Each step has two displays:

Page A

and

Page B

Display or Action

Explanation

03 TMMQFFFHC SCWSS*

This is

Page A

. In this example, the “03” at the left end of the dis-

play represents the formula number. The “01” below it represents
the step number within that formula. The

CWSS*

decisions

shown underlined repeat for each chemical programmed in this
step.

03 SPD D E

This is

Page B

. When the cursor is advanced past the last decision

Page A

Page B

appears for the remaining decisions in this

step. The decisions required on both pages vary according to ma-
chine model and options.

2.3.3.3.1

Actions when the Cursor is at the Step Number

BNCJUP03.C05 0000191943 C.2 D.2 B.3 1/2/20 1:16 PM Released

Display or Action

Explanation

03 TMMQFFFHC SCWSS*

Typical display with cursor at

step number

xxxxxxxxx xxxxxx

Indexes forward/backward through the step numbers in this
formula.
Accesses the selected step and positions the cursor at decision

or saves all changes and exits this formula if this is the last step of
an existing formula.

Exits this formula, clearing the formula if it has not been saved, or
discarding any changes to a previously existing formula.

2.3.3.3.2

Actions when the Cursor is at a Decision within a Step

BNCJUP03.C06 0000191942 C.2 D.2 B.3 1/2/20 1:16 PM Released

Display or Action

Explanation

03 TMMQFFF

C SCWSS*

02 xxxxxxx

x xxxxxx

Typical display with cursor at a d

ecision

within a step

Indexes forward/backward through the valid choices for this
decision.
Moves the cursor forward among

Pages A

and

through each

valid decision in a specific step. This accepts the standard or de-
fault decision if another choice was not previously made.

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 29 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: