Milnor E-P Plus Скачать руководство пользователя страница 24

Страница: 24 / 92

Pellerin Milnor Corporation

12. The

Door Unlock button

(

) functions normally during manual operation.

2.1.3

Control Functions During Programming

BNCJHP01.R03 0000189819 C.2 A.5 1/2/20 1:16 PM Released

The programming mode is used to modify the actions performed in a wash formula or to create
new wash formulas.

1. The

Start button

(

) is used in combination with the

Next button

(

) or the

Terminate

button

(

) to delete or insert a step in a wash formula, respectively.

2. The

Run/Program keyswitch

allows programming when set to

. The

Program menu

in-

cludes selections for adding and changing wash formulas, configuring the controller, and re-
storing the standard formulas provided with the machine. The keyswitch must be set to the

Run position

(

) for normal machine operation, as described in

2.1.1: Control Functions

During Normal Operation, page 15

3. The

Run Indicator light

is not actuated during programming.

4. Use the

Scroll Down button

(

) to change the selected programming parameter to the next

lower-numbered choice.

5. The display presents the programming menus and choices within those menus, including all

configuration and formula parameters.

6. The

Scroll Up button

(

) scrolls the available choices upward from the lowest available

number.

7. Use the

Next button

(

) to confirm any choice and move to the next decision in the

sequence.

8. The

Signal Cancel button

is not used in programming.

9. The

Operator Signal light

is not used in the programming mode.

10. The

Manual button

is not used in the programming mode.

11. The

Terminate button

(

) returns the user to the main programming menu (top line of dis-

play reads

Program X Menu

) from the

Add/Change Formula

and the

Standard Formulas

menus. The

Terminate button

has no effect after the

Configure menu

has been accessed, or

after any parameter of any formula has been accessed in the

Add/Change Formula

menu.

12. The

Door Unlock button

(

) is not used during programming.

BNCJVC01 / 2018382

BNCJVC01

0000181472

C.3

1/2/20 1:16 PM

Released

2.2

Selecting an Industry Formula Set

BNCJVC01.C01 0000181471 C.2 C.3 1/2/20 1:16 PM Released

This document gives data about all current Milnor

E-P Express

controlled washer-extractors

and Milnor

E-P Plus

controlled washer-extractors with one type of processor board. You can

identify this board by “P/N 08BH18EP_ ” near the Milnor

symbol on the processor board.

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 24 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: