Milnor E-P Plus Скачать руководство пользователя страница 45

Страница: 45 / 92

Pellerin Milnor Corporation

Drain speed.

After the last step, the basket coasts to a stop, then

accelerates to drain speed while the signal sounds. The basket
continues turning at drain speed with the signal on until the opera-

tor presses

to silence the signal and end the formula.

Tumble.

After the last step, the basket coasts to a stop, then be-

gins reversing at wash speed. After two minutes of tumbing, the
signal sounds. The basket continues tumbling at wash speed with

the signal sounding until the operator presses

to end the

formula.

Stopped with 2-minute buzzer.

This option is similar to the

Stopped

option, but the signal shuts off after two minutes. The

door unlocks after a delay. The operator can end the formula be-

fore this time expires by pressing

Reversing with 2-minute buzzer.

This selection is similar to

Reversing,

but the signal shuts off and the basket stops after two

minutes. The door unlocks after a delay. The operator can press

to end the formula before this time expires.

Drain speed with 2-minute buzzer.

This option is similar to op-

tion

2=Drain speed

, except the signal shuts off after sounding for

two minutes. The door unlocks after a delay. The operator can end

the formula before this time expires by pressing

Tumble with 2-minute buzzer.

This option is similar to

3=Tum-

ble

, except the signal starts when reversing stops and sounds for

two minutes, then shuts off. The door unlocks after a delay. The
operator can end the formula before this time expires by pressing

ADD/CHANGE FORMULA

RETURN TO MENU

Appears if step just previously programmed is the last step of the
formula. The controller is prepared for adding or editing another
formula, or returning to the

Programming menu

Returns to the

Program menu.

PROGRAM

0K TURN KEY TO RUN

This is the

Program menu

Saves changes and new formulas, then returns to the

Run mode

CAUTION:

Ensure programming changes are saved —

If the program key is turned

at this point, all programming changes will be lost when power to

the machine is turned off. Later software versions allow the person pro-
gramming the machine to correct the error, as described below.

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 45 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: